OWNER’SMANUALMODEL NO. 247.799640Caution;Read and Follow All Safety Rules and instructions Before Operating This EquipmentCRAFTSMAN9 HORSEPOWER
If necessary, use the tamper plug provided to push materia! into the chipper chute. See figure 8. NEVER PLACE HANDS INSIDE CHIPPER CHUTE.
Check the fuel level periodically to avoid running out of gasoline while operating the chipper-vacuum. If the unit runs out of gas as it is chi
CUSTOMER RESPONSIBILITIESo=>QOQCQ.Oil Pivot PointsClean Chipper-VacuumVVCheck Engine OilChange Engine OilVVService Air CleanerVClean Engine Cylinde
AIR CLEANERThe air cleaner prevents damaging dirt, dust, etc., from entering the carburetor and being forced into the engine and is importan
STORAGEPrepare your chipper-vacuum for storage at the end of the season or if the unit will not be used for 30 days or more.AWARNING: NEVER STOR
Hex Bolt Flat Washer Hex NutDischargeChuteAssemblyÇ Seif-Tapping ScrewsFIGURE 18.• Remove the two hex bolts and hex nuts which extend throug
CHANGING THE FRICTION WHEEL RUBBERThe rubber on the friction wheel is subject to wear and should be checked after 50 hours of operati
BELT REMOVAL AND REPLACEMENTASupportWARNING: Disconnect the spark plug wire and move away from the spark plug.• Remove the plastic belt cover
TROUBLE SHOOTINGPROBLEMPOSSIBLE CAUSE(S) CORRECTIVE ACTIONEngine fails to start • Fuel tank empty, or stale fuel.• Fill tank with clean, fresh fuel.•
SEARS CRAFTSMAN 9 H.P. CHIPPER-VACUUM MODEL NO. 247.799640Repair PartsREF.NO.PARTNO.DESCRIPTIONQTY.REF.NO.PARTNO.DESCRIPTIONQTY.11539-019PUSHNUT416 72
IMPORTANTSAFE OPERATION PRACTICESATHIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/
SEARS CRAFTSMAN 9 H.P. CHIPPER-VACUUM MODEL NO. 247.799640Repair PartsREF.NO.PARTNO.DESCRIPTIONQTY.REF.NO.PARTNO.DESCRIPTION QTY.1 629-0241 HARNESS—CH
SEARS CRAFTSMAN 9 HP. CHIPPER-VACUUM MODEL NO. 247.799640Repair PartsHEF.NO.PARTNO.DESCRIPTtONQTY.1 681-0078 IMPELLER ASSY COMP. (iNCL REF. NOS. 2 THR
SEARS CRAFTSMAN 9 H.P. CHIPPER-VACUUM MODEL NO. 247.799640Repair PartsREF.NO.PARTNO.DESCRIPTIONQTY.1 710-0230SCREW-HEX12710-0723SCREW-HEX 13 710-0896S
SEARS CRAFTSMAN 9 H.P. CHIPPER-VACUUM MODEL NO. 247.799640Repair Parts3123
SEARS CRAFTSMAN 9 H.P. CHIPPER-VACUUM MODEL NO. 247.799640Repair PartsREF.NO.PARTNO.DESCRIPTIONQTY.REF.NO.PARTNO.DESCRIPTION QTY.1618-0063BEARING ASSY
SEARS CRAFTSMAN 9 H.P. CHIPPER-VACUUM MODEL NO. 247.799640Repair PartsREF.NO.PARTNO.DESCRIPTIONQTY.1618-0168DIFFERENTIAL ASSY COMPLETE12 710-1206SCREW
SEARS CRAFTSMAN 9 H.P. ENGINE MODEL NO. 143.959003Repair Parts4003517^/182 /184<380/ ,239240 24^200186Jt*S8r--262^i>;Cr19_\J^g^^203y-----204286
SEARS CRAFTSMAN 9 H.P. ENGINE MODEL NO. 143.959003Repair PartsKEYNO.PARTNO.DESCRIPTIONKEYNO.PARTNO.DESCRIPTION1 35385Cylinder (ind. 2 & 20)102 650
SEARS CRAFTSMAN 9 H.P. ENGINE MODEL NO. 143.959003Repair PartsKEYNO.PARTNO.DESCRIPTIONKEYNO.PARTNO.DESCRIPTION28635446 Starter Screen37036261Instructi
SEARS CRAFTSMAN 9 H.P. ENGINE MODEL NO. 143.959003Repair PartsPARTS LIST FOR RECOIL STARTERKEYNO.PARTNO.DESCRIPTION590671 Recoil Starter1 590599ASprin
• Check and add fuel before starting the enigine. Never remove gas cap or add fuel while the engine is running. Allow engine to coo
Seal kits for the new cylinders are the same as for the oid cylinders, as all the internal components are the same.bore diam old cylinder new cylind
11. Very Important!!!! You must clean any paint or rust in the bore area by sanding it off. The paint will be from the snap ring groove outward. Afte
CONGRATULATIONS on your purchase of a Sears Craftsman Chipper-Vacuum. It has been designed, engineered and manufactured to give you the bes
TABLE OF CONTENTSSAFETY RULES...2. 3PRODUCT SPECIFICATIONS...4MA
ASSEMBLY INSTRUCTIONSFIGURE 2.IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL in the engine. After assembly, see operation section of this m
Hex Bolts, FiatFIGURE 5.DriveATTACHING THE CHIPPER CHUTE AND SUPPORT BRACKET (See figure 4)• Remove the two hex lock nuts from the hex bolts which
FIGURE 7.FIGURE 8.ATTACHING THE BAG• Place bag inside of handle assembly. Slip the opening on the bag over the discharge chute, making certai
MEETS ANSI SAFETY STANDARDSSears chipper-vacuums conform to the safety standards of the American National Standards Institute.OPERATING CONTROLS (See
Comments to this Manuals