Save This Manualr Future ReferenceMODEL NO,!t3.2!3080DRILL PRESS WITHMAXIMUM DEVELOPEDI/3 HP MOTORSerialNumberModel and serial numbermay be found at t
assemblyWARNING: FOR YOUR OWN SAFETY, NEVER CON-NECT PLUG TO POWER SOURCE OUTLET UNTILALL ASSEMBLY STEPS ARE COMPLETED.TOOLS NEEDED'[' _ ...
.4.Locate support lock handle among loose parts.Install support lock handle from left side into tablesupport. Raise table to working height by sliding
iNSTALLiNG FEED HANDLES!_ Locate three (3) feed handles among Iooseparts.2 Screw the feed handles tightly into the threadedhotes in the hub.iNSTALLING
BELT GUARD KNOB5ram DIA. x 12ram LONGSCREWiNSTALLING BELT GUARD KNOBBELT GUARD KNOB1, To attach belt guard knob, locate knob and 5mmDia x 12ram _ong p
ADJUSTING THE TABLE SQUARE TOHEADNOTE: The combination square must be "true." Seethe beginning of the "Assembly" section for a met
getting toknowpress1BELT GUARD/15FEED HANDLEFEED SPRINGADJUSTMENT19ON-OFF SWITCHFEEDSPRING9DEPTH POINTER16CHUCK2BELTTENSION LOCKHANDLE3HEAD LOCK SETSC
ThisDrillPresshas3 speedsaslistedbelow:620RPM!300RPM31OORPMSeeinsideofbeltguardforspecificplacementofbeltsonpulleys.SPINDLE SPEEDS BN R.P.M.1, BELT GU
Insert KEY into switch.NOTE: Key is made of yellow piestico1To turn drill ON . . .Insert finger under switch lever and pull.To turn drill OFF.,. Push
REMOVING THE CHUCK1. Open jaws of chuck as wide as they will go byturning chuck sleeve.2. Carefully tap chuck with mallet in one hand whileholding chu
basic dr!IS press operationFollow the following instructions for operating your drillpress to get the best results and to minimize the likeli-hood of
FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESSIf within one year from the date of purchase, this Craftsman Drill Press fails due to a defectin materi
POSITiONiNG TABLE AND WORKPIECELock the table to the column in a position so that thetip of the dritl is just a little above the top of the work-piece
WARNING: TO AVOID iNJURY FROM SPiNNiNGWORK OR TOOL BREAKAGE, ALWAYS CLAMPWORKPmECE AND BACKUP MATERIAL SECURELYTO TABLE BEFORE OPERATING DRILL PRESSWI
maintenanceWARNING FOR YOUR OWN SAFETY, TURNSWITCH "OFF" AND REMOVE PLUG FROM POWERSOURCE OUTLET BEFORE MAINTAINING OR LUB-RiCATiNG YOUR DRI
trouble shootingWARNSNG: FOR YOUR OWN SAFETY TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWERSOURCE OUTLET BEFORE "TROUBLE SHOOTING.
33PARTS LIST FOR CRAFTSMAN 8" DRILL PRESSMODEL NO. 113.21308034='Omo"O3O292827261624 1718 151920FIGURE 11/\7
r,o¢jnPARTS LiST FOR CRAFTSMAN 8" DRILL PRESSMODEL NO. 113.213080Always order by Part Number--Not by Key NumberFIGURE 1Key J PartNo. I No.8177712
repair partsPARTS LiST FOR CRAFTSMAN 8" DR_LL PRESSMODEL NO. 113.2130802\14Always order by Part Number--Not by Key NumberFIGURE 2Key PartNo. No.1
repair partsPARTS LIST FOR CRAFTSMAN 8" DRILL PRESSMODEL NO. 113.213080I 1fl 2j2Always order by Part Number--Not by Key NumberFIGURE 3 QUILL ASSE
fSERVICEMODEL NO.!t3.2t3080DREL PRESS WITHMAXIMUM DEVELOPEDI/3 HP MOTORHOW TO ORDERREPAIR PARTSi.i.LNow that you have purchased your 8-inch Drill Pres
additional safety instructions for driJl presses_VARNING: FOR YOUR OWN SAFETY, DO NOT_,TTEMPT TO OPERATE YOUR DRILL PRESSJNT_L RT _S COMPLETELY ASSEMB
b. Drum sanders must NEVER be operated onthis driU press at a speed greater than 1800RPMc. Do not install or use any drill that exceeds 7" inleng
gJossary of terms!. Workp_eceThe item on which the cutting operations is bei_gperformed.2. O_iglThe cutting tool used ir_the dritt press to make hoies
meter specifications and e ectricaJ requirementsMOTOR SPECIFmCATmONSThis drill press is designed to use a 1725 RPtvl motoronly. Do not use any motor t
unpacking and checking contentsWARNING: TO AVOID INJURY FROM UNEX-PECTED STAF_TING OR ELECTRICAL SHOCK, DONOT PLUG THE POWER CORD iNTO A SOURCEOF POWE
List of Loose Parts in Box 507870Item Description Qty.A Chuck Key ... 1B Chuck. ... 1List of Loose Pa
location and function of controls1. BELT GUARD... Covers pulleys and belt duringoperation of drill press,2. BELT TENSION LOCK HANDLES... Tighteninghan
Comments to this Manuals