Sears 113.298141 Owner's Manual

[Sears !ownersmanualMODEL NO.113.298141SAW ONLY113.298031SAW WITH LEGSTWO TABLE EXTENSIONSAND MOTOR113.298151SAW WITH LEGSONETABLEEXTENSIONAND MOTORSe

LayREARFENCE GUIDE BAR on table to act as astraightedge. If outer edge of extension is higher or lowerthan table surface;A. Slightly loosen nuts holdi

9, Nold rod with one hand and with a 1/2 in. wrench orpliers start screwing on ONE of the nuts only A TURNOR TWO... screw on other nut the same way.10

ALIGNING RIP FENCEThe fence should slide easily along the bars and alwaysremain in alignment (parallel to sawblade and miter gaugegrooves).The alignme

If the fence does not slide easily along the bars, the pressureof the spring can be REDUCED.1. Loosen the screws.2. Move spring slightly toward rear o

INSTALLING BLADE GUARD1. From among the loose parts, find2 Hex Head Screws, 1/4 - 20 x 5/8 in. long2 Hex Head Screws, 5/16 - 18 x 5/8 in. long2 Hex He

9. Raise blade all the way up . .. make sure it is _quarewith table.10. Raise Blade Guard ... lift up both ANTIKICKBACKPAWLS ... insert one of the SET

16.PlaceRIPFENCE on table ...CAREFULLY move it against blade so that it is parallelto the blade, and just TOUCHES tips of saw teeth ...tighten RIP FEN

11. Lift motor and insert the TWO PINS on motor baseinto HOLES in cradle ... push motor in asfar as it willgo.12. Lower the blade...install belt on sa

INSTALLING BELT GUARD1. Remove the belt and motor pulley.2. Screws furnished witli guard are "self threading" ...screw them into holes in BE

Press guard onto support so that bottom of guard isapproximately 3/4 in. away from belt.NOTE: To remove guard, lift up on LONG TABS ofcl ps ... pull g

FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAWIf within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material

GETTING TO KNOW YOUR SAW_1 SAWSLADETABLEINSERTMITER GAUGE |0 EXACT-I-CUT\LOCK HANDLE6 MITER GAUGE7" BLADE GUARDANTIKICKBACKPAWLSRiP FENCERIP FENC

2 ELEVATIONHANDWHEEL...elevatesorlowerstheblade.Turnclockwiseto elevate... counterclockwisetolower,3 TILT HANDWHEEL... tilts the bladefor bevel'

9 REMOVING AND INSTALLING SAWBLADE.WARNING: FOR YOUR OWN SAFETY, TURNSWITCH "OFF" AND REMOVE PLUG FROMPOWER SOURCE OUTLET BEFORE REMOVING OR

BASIC SAW OPERATIONWORK HELPERSBefore cutting any wood on your saw, study all of the"Basic Saw Operations".Notice that in order to make some

CROSSCUTTINGCROSSCUTTING is known as cutting wood acrossthe grain, at 90 °, or square with both the edge and the flatside of the wood, This is done wi

1. NEVER USE THE RIP FENCE AS A LENGTH STOPBECAUSE THE CUTOFF PIECE COULD BINDBETWEEN THE FENCE AND THE BLADE CAUSINGA KICKBACK,2. When making repetit

USING THE RIP FENCERIPPING, BEVEL RIPPING, PLOUGHING, MOLDING, not DIG into the workpiece and HOLD it... the pawlsRESAWING AND RABBETING are performed

When "WIDTH OF RIP" is 2 in. to 6 in, wide USE THEPUSH STICK to feed the work.When WIDTH OF RIP is NARROWER than 2 in., the pushstick CANNOT

RESAWINGRESAWING is known as ripping a piece of wood throughits thickness. Do not attempt to resaw BOWED orWARPED material. NOTE: To RESAW a piece ofw

ADJUSTMENTSWARNING: FOR YOUR OWN SAFETY, TURN SWITCH"OFF" AND REMOVE PLUG FROM POWER SOURCEOUTLET BEFORE MAKING ANY ADJUSTMENTS.BARLOCK KNOB

ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWSWARNING: FOR YOUR OWN SAFETY, DO NOTOPERATE YOUR SAW UNTIL IT IS COMPLETELYASSEMBLED AND INSTALLED ACCORD

6. If tooth does not touch the same amount ... themechanism underneath must be adjusted to make theblade PARALLEL to GROOVE.A. Rear trunnion must be m

3. Operate the tilt-lock handle (COUNTERCLOCKWISE)to loosen the tilt clamp screw.4. NOTE: Handle is spring loaded for engagement withscrew head - must

If b! ade is NOT 45 ° to table.., the 45° STOP COLLARand SCALE must be ADJUSTED, _1 Remove Elevation Handwheel. _ 0 °2. Using a small size screwdriver

LUBRICATIONThe following parts should be oiled occasionally with SAENo. 20 or No. 30 engine oil.1. Tilt screw threads and pivot nut. (First Clean with

TROUBLE SHOOTINGWARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWER SOURCEOUTLET BEFORE TROUBLESHOOTING.TROUBL

TROUBLE SHOOTING -- MOTOR (Continued)TROUBLEMotor starts slowlyor fails to come upto full speed.3.IMotor overheats. 1.2.Starting switch inmotor will n

o,163PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAWMODEL NO. 113.298141, 113.298031 & 113.2981517 8 910141620 193635282930 3132 31!Figure I332726 25i-

(,}PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAWMODEL NO. 113.298141, 113.298031 & 113.298151Always order by Part Number - not by Key Number.FIGURE 1

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAWMODEL NO. 113.298141, 113.298031 & 113.2981511 234 5 6 76564624445439101213143141 4O18 19 20Iut 25I38 37

_OPARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAWMODEL NO. 113.298141, 113.298031 & 113.298151FIGURE 2 PARTS LISTKey PartNo. No. Description12345678910

R. DO NOT remove small ;)ieces of cut-off materialthat may become trapped inside the blade guardwhile the saw is running. This could endanger yourhand

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAWMODEL NO. 113.298141, 113.298031 & 113.2981519 10 112 34 5I13FIGURE 3 -- 62705 FENCE ASSEMBLYKey { PartN

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAWMODEL NO. 113.298141, 113.298031 & 113.29815114FIGURE 4 -- 62704 MITER GAUGE ASSEMBLYKey PartNo. No. Des

PARTS LJST FOR CRAFTSMAN 10 INCH TABLE SAWMODEL NO. 113.298141, 113.298031 & 113.29815112\\53 4FIGURE 6 -- ON/OFF POWER OUTLET 603816KevlNo.J12:3_

PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAWMODE L NO. 113.298141, 113.298031 & 113.2981514 55 4122,FIGURE 8 -- LEGS SUPPLIED WITH113.298031 AND 113

Sears IownersmanualSERVICEMODEL NO.113.298141SAW ON LY113.298031SAW WITH LEGSTWO TABLE EXTENSIONSAND MOTOR113.298151SAW WITH LEGSONE TABLE EXTENSIONAN

Plug power cord into 110-120V properly grounded typeoutlet protected by a 15-amp. time delay or Circuit-Saverfuse or circuit breaker,IF YOU ARE NOT SU

UNPACKING AND CHECKING CONTENTSTOOLSNEEDEDMedium ScrewdriverSmall ScrewdriverP,ie, , WrencheI,I.:,:I',I.I_i,II'Z_ 3/8 in. 7/16 in.1/2 in. 91

ItemPartName Qty.Z HexNut, 5/16-18(approx. dia. of hole 5/16 in.) ... 9Z HexNut, 1t4-20(approx.dia.of hole 114in.) ... 2AA Lockwasher

4.To remove insert.A) Loosen ScrewB) Lift insert from front end, and pull toward front ofsaw,To replace insert.Place insert into insert opening in tab

MOUNTINGSAW1. From among the loose parts, find the followinghardware:4 Hex Head Screws. 5/16 - 18 x 1-1/4 in. long.4 Hex Nuts, 5/16- 18 (approx. dia.