Sears CRAFTSMAN 139.53640SRT User Manual

OWNER’SMANUALModel No. 139.53525SRT 139.53627SRT 139.53636SRT 139.53640SRT 139.53641 SRTFor Residential Use OnlyCaution;Read and follow all safety rul

Assembly Step 4Install the Chain/Cable & Attach the Sprocket CoverDispensing CartonLeave Chain and Cable Inside Dispensing Carton to Prevent Kinki

Assembly Step 5Tighten the Chain & Cable• spin the inner nut and lock washer down the threaded shaft, away from the trolley,• To tighten the chain

Installation Section: Pages 12-27Installation Step 1Determine Header Bracket Location Installation procedures vary according to garage door types. Fol

ONE-PIECE Door Without TrackRead the Safety instructions on page 12. They also apply to doors without tracks.Close the door and mark the inside vertic

Installation Step 2Install the Header BracketYou can attach the header bracket either to the wall above the garage door, or to the celling. Follow the

Installation Step 3Attach the T-rail to the Header BracketHeader Wall• Position the opener on the garage floor below the header bracket. Use packing m

Installation Step 4Position the OpenerFollow instructions which apply to your door type as illustrated.A CAUTIONTo prevent damage to steel,

Installation Step 5Hang the OpenerA WARNINGThe opener could fall and Injure someone If It is not properly secured. Fasten the opener sec

Installation Step 6Install the Deluxe Lighted Console Wall Control• strip 1/4" of insulation from one end of the bell wire; connect the wire to t

Installation Step 7Install the Lights and the LensesInstall the lights:• Install a 75 watt maximum light bulb in each socket. The lights will turn ON

Contents PageA review of safety alert symbols...2You'll need tools..,,...,,...,,...

Installation Step 9Electrical RequirementsTo reduce the risk of electric shock, your garage door opener has a grounding type plug with a third groundi

The Safety Reversing SystemInformation you'll need before you begin the installation of the safety reversing sensor.The safety reversing sensor m

Installation Step 10Install the Safety Reversing SensorFigures 2 and 3 show assembly of brackets and "C" wrap based on the recommended insta

Insert the wire connector into each sensor and push until you hear a click, Figure 6, The white tab on the sensor should be flush with the back of the

Installation Step 11Fasten Door BracketFollow instructions which apply to your door type as illustrated below or on page 25.A CAUTIONTo prevent

All ONE-PIECE Door Installation ProcedurePlease read and comply with the warnings and reinforcement instructions on page 24. They apply to

Installation Step 12Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on page 27.SECTIONAL Doors

All ONE-PIECE DoorsAssemble the Door Arm:• Fasten the straight and curved door arm sections together to the longest possible length, wit

Adjustment Section: Pages 28 - 30Adjustment Step 1Adjust the UP and DOWN LimitsDo not make any limit adjustments until the safety reversing sensors ar

Adjustment Step 2Adjust the ForceForce adjustment controls are located on the right side panel of the opener. Force adjustment settings regulate the a

You'll Need ToolsDuring assembly, installation and adjustment of the opener, instructions will call for hand tools shown below.A. WARNINGAn unba

Adjustment Step 3Test The Safety Reversing Sensor• Press the remote control push button to open the door.• Place the opener carton in the path of the

IMPORTANT SAFETY INSTRUCTIONSA WARNINGWARNINGTo reduce the risk of severe injury or death to persons:1. READ AND FOLLOW ALL INSTRUCTIONS.2. Do not per

Operation of Your OpenerActivate the opener with any of the foiiowing devices:1. The 3-Function Remote controi. Hold large push button down until the

Receiver and Remote Control ProgrammingTo comply with FCC rules, adjustment or modifications of this receiver and/or transmitter are proh

Having a Problem?Situation Probable Cause and SolutionThe opener doesn't operate from either the Wall Control or the remote control:1. Does the o

Having a Problem? (continued)Situation Probable Cause & SolutionThe door opens but won't close:1. If the opener lights blink, check the safet

Repair PartsRail Assembly PartsKEYNO.PARTNO. DESCRIPTION1 1A995 Master link kit2 41A3489 Complete trolley assembly3 1B3117 T-rail - center section4183

Repair PartsOpener Assembly PartsKEY PART NO. NO.DESCRIPTIONKEYNO.PARTNO. DESCRIPTION31D38041C4220A41A281741B424541C425341A4315-6B41A4351175B88Sprock

AccessoriesSears offers many useful accessories for your garage door opener. They are illustrated below with Sears model numbers and des

IndexAccess Door/Outside Key Release Accessory...

SECTIONAL Door InstallationBefore you begin, survey your garage area to see whether any of the conditions beiow apply to your installati

OWNER’SMANUALModel N0= 139=53225SRT1 139.53325SRT1 139.53425SRT1 139=53628SRT1 139.53629SRT1 139.53635SRT1 139.53637SRT1 139.53824SRT1The model numbe

ONE-PIECE Door InstallationBefore you begin, survey your garage area to see whether any of the conditions below apply to your installation.One-Piece D

opener Carton inventoryYour garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is missing, carefully

Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation proc

Assembly Section: Pages 8 ™ 11To avoid installation difficulties, do not run the garage door opener until instructed to do so.Assembly Step 1Assemble

Assembly Step 3Fasten the T-raii to the OpenerA CAUTION• Place the opener on packing material to protect the cover. For convenience, put a support und