Sears 113.206931 User Manual

;\Save This Manual' Por Future ReferenceearsownersmanualMODEL NO.113.206801JOINTER/PLANER ONLY113.206931JOINTER/PLANER WITH LEGS AND MOTORSeria

assembly3, toosfr' àetsJ'i'iW {n motor pulley and piace pulley ;ón shaft wHh hub flush with ertcf of shaft, insert iP

8. Snap guard ‘nto position as sóowft.9. Rt?!'nov8 knoO find vATisher , . , isft gusKii up.!0. Lt>ost?n Th* two MOTOR BASE CLAMP SCREWS

getting to know your joirster-plonerWARNING: FOR YOUR OWN SAFETY TURN SWITCH “OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MA

b. Before tightening fence lock knob, ho!d fence down on outfeed table so it does not rock,c. 90*^ Fence Stop positions fence square to

getting to ;know your ¡©infer»planer: e. Adjust 45? stop in the same manner.: NOTE: Tilt scale will not require adjustment if itwas adjusted for 90*^

a. Insert a pencil in space at end of cutterhead to hold cutterguard open.b. Place a straightedge (large square or long level) on outfeed

getting to know your ¡oinfer-plonerh. Loosen four lock screws 2 or 3 turns with 1/2 ir>.‘ wrench.VIEW LOOKING UP FOR PARTS IDENTIFICATIONTurning

b. To turn machine on, insert finger under switch lever and puli end of switch outc. To turn machine OFF.. - PUSH lever in.Never leave machine unatte

bo$îc ¡oinfer-pîooer operofîoiiFor your own safety, ALWAYS use th6 hold down/push blocks when JOINTING wood that is NARROWER than 3 in

Always feed WITH THE GRAIN whenever possible. If the nature of the workpiece i$ such that it must be fed AGAINST THE GRAIN, take

FULL ONE YEAR WARRANTY ON CRAFTSMAN JOINTER/PLANERIf within one year from the date of purchase, this Craftsman Jointer/Planer fails due

basic ¡oinfer-ploner operationWhen planing wood 3/4 in. thick and NARROWER than the. hold down/push block, tilt the hold down/push bloc

maintenanceBLOCK OF WOODREPLACING CUTTER BLADESWARNING; FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOUFiCE

maintenance7. Remove the six lifter screws, (Two under each blade^l8. Clean cutterhead, wedges and screws thoroughly with Craftsman Gum and

INSTALLING CUTTER GUARD SPRING1. Remove cotter pin from pivot pin in cutter guard and remove guard (located underneath infeed table.)Spring must ap

moinfenanceThe normal position of guard (at REST) when fence is stationed at IVIAXtSVlLUVI WIDTH OF CUT, is shown as "position &qu

generai mainteriarìceKeepyour jointer-planer dean. Put a carton or some kind of a Container underneath your jointer-planer to catch the

le shootingWARNING: FOR YOUR OWN SAFETY, TURN SWITCH "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLE SHOOTING

air parts :CRAFTSMAN 61/8 !fSlCH JOINTER-PLANER MODEL No. 113.206801 AND 113.2069311-FIGURE 1 -- LEGS PARTS LISTFIGURE 1KeyNo.PartNo.Description1 67

ю09ФQÚ iñ

CRAFTSMAN 6-1/8 INCH JOINTER-PLANER MODEL No. 113.206801 AND 113.206931FIGURE 2 PARTS LISTN3(DKeyNo,PartNo.Description1ST0512505‘Screw, Pan Hd. 1/4-20

addlitîôiiali;$ifety; iftstrécfSafety is a combination of operator common sense and alertness at all times when the Jointer-Planer is being us

repair parts : :CRAFTSMAN 6 1/8 INCH JQINTER PLANER MODEL No, 113.206801 AND 113.206931FIGURE 3FIGURE 3 INFEED TABLE PARTS LISTKeyNo,; Part No.Descr

CRAFTSIV1AÌ4 6-1/8 INCH JOINTER-PLANER MODEL No. 113.206801 AND 113.2069311 2 3 4 5 6 7FIGURE 4FIGURE 4 -21013 FENCE ASSEMBLY PARTS LISTKeyNo.Pa

earsownersmanuaiSERVICEMODEL NO. 113.206801JOINTER/PLANER ONLY113.206931JOINTER/PLANER WITH LEGS AND MOTORHOW TO ORDER REPAIR PARTS6-1/8 INCH JOINTER-

oddifiono! sofety: insfrycfioriS'for ¡©inter^plaiiér13. To be sure you will make a depth of cut as planned, always lower the infee

rtiotor specifications and é!éctrical re^uireriieiitsThis machine is designed to use a 3450 RPM motor only. Do not use any motor that

urspacking and checking confetifsTOOLS NEEDED1/2" Wrench 7/16" Wrench 3/4" Wrench 3/8" WrenchI M' ttMedium ScrewdriverI . IMo

unpacking and checking contentsTABLE OF LOOSE PARTSThe Following Parts Are Included WithModel 113.206931 OnlyNo.Description Qty.ALeg ...

assemblyM0UMT1NG JOINTER-PLANER1. From amontj the loose, parts, find the followinghardware; . .4 Carriage Bolt, 5716-18 X 3/4 : ..3 Hex Head Sc

INSTALLING SLIDING GUARDPARTS NEEDED1/2 IN, HEX NUTSliding Guard Sliding Guard Knob Sliding Guard RodSliding Guard Washers ions side of washer is conc