Sears 486.248463 User Manual

46"- 2 STAGE SNOW THROWERTRACTOR ATTACHMENTModel No. 486.248463Owner's ManualCAUTION:Before using this prod uct, read this manual and fol lo

10FIGURE 17 LEFT SIDE VIEW• Remove the nylon tie which fastens the chute crank rod to the crank support tube.• Assemble the crank support tube (fl

11FIGURE 19 RIGHT FRONT CORNER VIEW • Coat the top of the ring around the dis charge open ing with general purpose grease. See fi gure 19.• Place t

12AUGER BELT• Make sure the auger belt is correctly assembled to the snow thrower. The belt must pass over the top of the auger pulley and then twist

13Hold this diagram above you while viewing the Clutch/Idler Assembly from underneath the tractor. Right and left in this diagram will be the reverse

14• Place the weight keg on the weight tray and fi ll with approximately 100 lbs. of dry sand.• Secure the keg with the rubber tarp strap hooked into

15OPERATIONKNOW YOUR SNOW THROWERRead this owner's manual and safety rules before operating your snow thrower.Compare the illustration below with

16• In extremely deep snow, raise the snow thrower from the ground to remove the top layer and drive forward only until the tractors front tires reac

17Service DatesCheck for loose fasteners X Check for loose fasteners X Check belts for wear X X Check belts for wear X X Che

18SERVICE AND ADJUSTMENTSFIGURE 27REPLACING AUGER BELT• Raise the snow thrower to the transport position.• Release the spring tension on the drive b

19STORAGECAUSEPROBLEMCORRECTION Clogged discharge chute Clogged discharge chute Spiral augers stop turning Snow thrower stalls tractor engine1. Upper

2TABLE OF CONTENTSACCESSORIES ...2SAFETY RULES ...

20PARTSREPAIR PARTS FOR MODEL 486.248463 46" SNOW THROWER11021212929232425833938272831323313 13 343536 32373338394032134243443845461347113213

21REPAIR PARTS FOR MODEL 486.248463 46" SNOW THROWER REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO.1 63576 1 Hou

22REPAIR PARTS FOR MODEL 486.248463 46" SNOW THROWER1234578910111513131412161617 17182020202019619191920 2014212222242422232325552626552728272826

23 REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO. NO. NO. 1 24820 1 Lift Bracket

24NOTES

25NOTES

26NOTES

27A POWER POLEA CORNER OF A BUILDINGOR A FENCE POSTFOLD ALONG DOTTED LINE, REPRESENTING A 10 DEGREE SLOPESIGHT AND HOLD THIS LEVEL WITH A VERTICAL TRE

Get it fixed, at your home or ours!For repair of major brand appliances in your own home…no matter who made it, no matter who sold it!1-800-4-MY-HOMES

3SAFETYAny power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution a

4HARDWARE PACKAGE CONTENTSREF. QTY. DESCRIPTIONREF. QTY. DESCRIPTIONREF. QTY. DESCRIPTIONN 2 Bowed WasherN 2 Bowed WasherO 6 Washer,

5CARTON CONTENTS1. Frame Brackets (2)2. Hanger Bracket, L.H. 54"3. Hanger Bracket, R.H. 54"4. Hanger Bracket, L.H.5. Hanger Bracket, R.

6(2) 7/16" Wrenches(2) 1/2" Wrenches(2) 9/16" Wrenches(1) 5/8" Wrench or Adjustable Wrench(1) 11/16" Wrench or Adjustabl

7FIGURE 4 RIGHT SIDE VIEW• Assemble the L.H. hanger bracket to the left side of the tractor frame using two 3/8" x 1" hex bolts, two 3/8

8• Remove and store the mower stop bracket and bolt from both sides of the tractor frame. See fi gure 3.• Remove the two bolts from the bottom of the

9FIGURE 12 RIGHT SIDE VIEWFIGURE 11If your mower deck is 54" skip this paragraph.• Attach the rear of the clutch/idler assembly to the tractor