OWNER'SMANUALMODEL NO. 536.886331HOW TO ORDER REPAIR PARTSCRAFTSMAN10 HORSEPOWER 29" DUAL STAGE 120V. ELECTRIC START SNOW THROWERWHEN ORDER
ASSEMBLYTO INSTALL THE SHIFTER LEVER• Stand the snow thrower up on the front of the auger housing, as shown in FIG.8A. Note: Place a piece of cardboa
OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW jj_|pOWER. Compare the illustrations wit
OPERATIONThe operation of any snow throwercan result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear
OPERATIONTO USE WHEEL LOCKOUT PIN• The left hand wheel is secured to the axle with a klick pin (See FIG. 5A). This unit was shipped with this klick p
OPERATIONACAUTION: GASOLINE IS FLAMMABLE AND CAUTION MUST BE USED WHEN HANDLING OR STORING IT.DO NOT FILL FUEL TANK WHILE SNOW THROWER IS RUN
OPERATIONA CAUTION: THIS STARTER IS EQUIPPED WITH ATHREE-WIRE POWER CORD AND PLUG AND IS DESIGNED TO OPERATE ON 120 VOLT AC HOUSEHOLD CURRENT. I
OPERATIONIACAUTION: DO NOT ATTEMPT TO REMOVE ANY ITEM THAT MAY BECOME LODGED IN AUGER WITHOUT TAKING THE FOLLOWING PRECAUTIONS:• RELEASE AUGER DRIV
CUSTOMER RESPONSIBILITIESSERVICE RECORDSFill In dates as you complete regular serviceSCHEDULESERVICEDATESAfter First 2 hoursBeforeEachUseAsNeededEver
SNOW THROWERlubrication - EVERY TEN HOURS• Auger Shaft - Using a hand grease gun, lubricate the auger shaft zerk fittings (See A, FIG. 2) every ten (
CUSTOMER RESPONSIBILITIESLUBRICATION• Hex Shaft and Gears - Hex shaft and gears require no lubrication. All bearings and bushings i»'"® lif
ACAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE ANDPLACE WIRE WHERE IT CANNOT CONTACT SPARK PLUG TO PREVENT ACCIDENTAL STARTING WHEN SETTING-
SERVICE AND ADJUSTMENTSACAUTION: ALWAYS DISCONNECT THE SPARK PLUG WIRE AND TIE BACK AWAY FROM THE PLUG BEFORE MAKING ANY ADJUSTMENTS OR REPAIRS.
TRACTION DRIVE LEVER"Z" FITTINGCONTROL LEVER MUST BE IN FULL FORWARD POSITION (Just Contacting Plastic Bumper) WHEN CHECKINGPLASTIC BUMPER
SERVICE AND ADJUSTMENTSTO REPLACE BELTSThe drive belts on this snow/ thrower are of special construction and should be replaced with original
SERVICE AND ADJUSTMENTSTRACTION DRIVE BELTif your snow thrower will not move forward, check thetraction drive belt for wear. If the traction drive bel
SERVICE AND ADJUSTMENTSTO REPLACE FRICTION WHEELIf the snow thrower will not move forward, and the friction wheel is worn or damaged, you need
SERVICE AND ADJUSTMENTSTO REPLACE AUGER SHEAR BOLTThe augers are secured to the auger shaft with special bolts (See FIG. 16) that are designed to brea
SERVICE AND ADJUSTMENTSTO ADJUST OR REPLACE THE SPARK PLUGIf you have difficulty starting your snow thrower, you may need to adjust or replace th
STORAGEA CAUTION: NEVER STORE YOUR SNOW THROWER INDOORS OR IN AN ENCLOSED, POORLY VENTILATED AREA IF GASOLINE REMAINS IN THE TANK. FUMES MAY REA
TROUBLE SHOOTING POINTSTROUBLECAUSECORRECTIONDlfficull atartingDefective spark plug Water or dirt in fuel systemReplace defective plug.Use carburetor
SAFETY RULES• Never operate the snow thrower near glass enclosures, automobiles, window welis drop- offs, and the like without proper adjustment of t
CONGRATULATIONS on your purchase of a Sears Craftsman Snow Thrower. It has been designed, engineered and manufactured to give you the be
TABLE OF CONTENTSSAFETY RULES...2,3PRODUCT SPECIFICATIONS...4CUSTOMER RESPONSIBILITIE
CONTENTS OF HARDWARE PACKCONTENTS OF PARTS BAGe*2- Spare Shear Bolts (1/^0 X 1-3/4 In.)1- 3/8 -16 X 2.00 In. Hex Head Bolt1 - Knob With Threads (not s
ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY1' Knife (to cut carton and plastic ties;2 ' 1/2 inch wrenches (or adjustable wrenches)2 - 9/16 inch wren
ASSEMBLY• Assemble the snow chute.• Roll snow thrower oif the skid by pulling on the handle.• Properly dispose of discarded packaging.HOW TO SET UP
ASSEMBLY• Bend the ends of the colter pin around the rod and reinstall the plastic cap.• Tighten the eye bolt installed earlier, keeping oye in line
Comments to this Manuals