Sears 358.357182 User Manual download pdf (Page 10)

E. BAR AND CHAIN UfBfUCANT

• TheguidebarnfMfcuttingcfialnfwjwreconstant

lubrication to mmatn in operating condition.

LuiDrcatxsn IS crovided by trte auaxnatfc oiler system

wner: tre ori tank is kept filled.

—Luck of lubricant wQI puicidy niio the bar and

chain,

—Too itttie lubricant will cause overheatirig

shown oy smoke coming from the cham andtof

discoloration of the guide bar rails.

• Use Sears Bar and Chain litbricam f#71>36SS4>

gal. or #71-36S55kM to fill the oil tonic Clean SA£

30W oil may also be used, but is less affective. JVmmr

use wasm oS for this purpose.

• *nfreezingweatherollwiIltWck8n,maidngan«ei.

sary to thin bar and chain oil with a atnail amount

of f1 Oie$elPuetori^resene.Sarandch3inoi!must

be free Rovring fer adeqtaiE iubncsSofi.

1. USE THE FOiXOWING;

30® Of above — lubtKant undilutad

30® to 0®F. — 9S% Udjricant to S%

tf Oiasei futi or Ketosene;.

Below 0®F. — 90% Lubricant to 10%

fi Diesel futi or iferos^tt.

2. HOW TO RLL THE OIL TANK

a. Turn saw on its side with oil cap up. Figure

13.

b. Loosen cap slowly; wait tor pressure in the

tank to be released before removing the

cap. .

c. Fill the oil tank.

d. Replace the oil cap securely.

3, IMPOmr^POINre-TOHEMEMBER

a. Fit! the oil tank each lime you rtfllf the fuel

tank to ensure there will be sufficient oil for -

the chain whenever you start and run the

saw.

" »

b. n is normal for a small amount of ail to ap

pear under the uw after the angin« stops

due to oil draining from the bar and chain.

Figurais

USING YOUR SAW

A. PRE-OPERAnON CHECKS

Each time before operating your saw, always:

1. «'Check over safety rules and pteeauiions in

this manuat. Make certain you completely

understand and can apply each one.

6, «•Cheek №a fuel lank and oil tank. Both tanks

should be filied.

2. ''Cfwcfcpwlecthragetr.Alwaysuseeye.hoaritsg,

and head protection devices: safety footwear; pn>-

teahra gloves: and snugfittingefothkig.

1 «'Cheticthesawtortoeeebolts.mito.orflttings.

Tighten, repair or rapiaee parts as necessary. Tools

required are lisrad inthe “Assembly"

4. «•Check the eirfStcr. Clean the fOfer if dirty, before

starditg the engirm Fbr location, see the “Air niter"

SBCtXüO*

5. Check ttie saw chain. The chain should be snaip

and ai the correct tension. (Refer to the “‘Chain Ten-

son * Sedion). ' ■

«•Check the handies. Handles should be dry

and free of fuel mixture and oil. .

I. «'Check weather conditions. Do not use your

saw at night or dunng bad conditions such

as strongjwind. ram, snow. etc.

g. «'Cheek the work araa. Keep children,

bystanders, and antmaisasafe distance away

tram the work area when starting or ooeralmg

the sawa minimum of 30 feet.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Comments to this Manuals

No comments

Sears 358.357182 User Manual Page 10

Comments to this Manuals