Sears 358.357182 User Manual download pdf (Page 20)

tS. fleotaca Boileyimiw housing; £te sure the pyliey в

all the wsy Рмп and the spimg tssemred.

ia Repface and tighten puley screw. Rgute 41.

17, Hoki the 10 inch stack in the rope anetcaich reps in

pulley notch. Ядшв42.

ie. HoidthetooetautandmaJe2cofT45i0®tumsofiite

pufley dactcvmse to place tension on thepuJIey.

Hoto the puJleyto retain tension, ’

19. Align pulley notch with rope exit hoie. pull stairer

handle и the full extemot the rope and allow the

rope to rewind stowty.

20. flemsall the fen housing.

Figure 42

1. CARBUfierOR AO^tlSTMCNTS

• ThocartJtÄWDThasbeenacSusadattfteiBaofyforsaa

leveloorieStiQns.A:|ustmenisiTiaybecsRHinecessary

if the saw « used at signScanöy higher aitiftides or if

you riotice any of the fetfowing coriditiofls:

MOTE; Be sure to properiy prepare the saw as

described in ”1. Freparttfon,'*beiawbeiorefnaJdng

any adjustmens.

»Chain moves when the engine runs ai idie

speed. See **2, idle Speed ^ustment."

— Saw will not icSe. See “2. Idle Speed Adiust-

tnent" and *^LCMrSpeed№Ai«e Adjustment.”

—losaef cutting power which isnot cornered hy

airfifterdeaniog. See “S High Speed Mixture

Adfustment”

— Enginediesorfresireteswhenitsfaeuidacceie

rate. See “4. Acceteration Adjustment."

iiSoTiQW:] l%inuMHUdainagewiHocatrtoany

2-«yde engine if incotrect carburetor adust*

menti are mads.

• Iftheenginewianoteperiteprapertyafrermak*

ing these a^ustmenb, take the saw to yourSeers

Service Cenret/Deparmtent.

— A WARNING ^ 1

The chain may be moving dutitig moat of this pro.

cedut«.1AfearyQurprfltecttvegaarandfoikiwaltt^dy

fnsaruetlorta.

1. PREPARATTON

a. Slop engine.

b. Use a fresh fuel mixture with proper gasoiiney

oiirsia

c PfeoethesaMronasoijd,fiatsurfaoeandmaÉBsixe

the cfttój wfl! «xeotniaatiy obfaet

d. Remove the carburetor cover screws and

carburetor cover (Figuress} and locare itie

thiee(3)carbure«)rai^usting screws. Figta«4S^

e-StarttheengirreandaftiwengiriereidteS minutes

to warm up. The engine must be at ^¡msamg

tampetatum for pioparae^ustmstns tot» matte.

CHOKE CtOSS)

HIGH SPEED

MIX SCREW

tOI£ SPSS

SCREW

LOW SPEED

MIX SCREW

Figura43

2. lOUE SPEED AOIUSTMENT

a. ASowen^toidle

0. Adjust idieSpaadScna until engine continues :p

nxvwittioutSfeflMigandwithoutlriecnainrTKmng

—■ screw dockiHse to increase eogine

speed ff engine stant or (bes.

— Um same eountBtc/oM'tme w sk’w ermine

down anopr to Jmep ttie cham tram turning,

c Mo further ac^jstmems are necessary if the

chain does not moMtatidle speed ahdifpetfor.

mairet is sattafuttory.

ikWARNING

RecfwckfafleiMtaadafreraeeh adjustment ^ew. The

chain iiHist not move at idfa spi^ to avoid serious

injury, ■

3. UOW SPEED MXTURE ADJUSTMENT

a Anew engine to idit.

b Turn the Low Speed Mixture Screw siowiy

ctockwBe urea the RPM stans to drop Note

ttieposhioiw ■

c TremheLowSpeedlSxtureScrewooumerckxik.

wise untif the RPM speeds up and stans to crop

a^ii. NoM the posttion.

d. Sd die low Speed Mixhjm Screw at the m«j.

pomt berereen the twoposroons.

4. ACCe^ERAtlON ADJUSTMENT

If enginedies Of heshatesinsreadef accelerating.turn

ttieiowSfNMMt IfixtureScrew i/tS of a turn at a

tune counterdodewise until you have smootn

tKxteierabon.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 31 32

Comments to this Manuals

No comments

Sears 358.357182 User Manual Page 20

Comments to this Manuals