8EAIRS"Model No. 831.159330Serial No.The serial number can be foundin the location shown below.Write the serial number in thespace above.Serial N
20. 201021.22.Slide a 3/8" Flat Washer (16), one end of the17" Cable (51) and a Spacer (62) onto a 3/8"x 2 3/4" Bolt (10).Insert t
23. Insert the 125" Cable (52) through the "1"Plates (43). The ends of the "1"Plates withthe three holes should be downward.S
1226. Route the 258" Cable (53) under a SmallPulley (1). Attach the Small Pulley to thelower end of the Weight Upright (31) with a3/8" x 3 1
30. Insert the Clevis Pin (60) through one of thethree holes in the Weight Upright (31). Insertthe Hairpin Cotter (61) through the Clevis Pin.Note: Th
144.35.Slide a Cable Trap (3) and a Small Pulley (1)onto a 3/8" x 2" Bolt (9). Route the 258" Cable(53) over the Small Pulley. Make sur
37. Route the 258" Cable (53) around a SmallPulley (1). Attach the Small Pulley to theButterfly Frame (24) with a 3/8" x 1 3/4" Bolt(8)
41.42.Insert a 3/8" x 2 3/4" Bolt (10) through theindicated hole in the Leg Lever (28).Slide a Small Pulley (1) and a Cable Trap (3)onto the
45.46.Insert one Pad Tube (71) through theButterfly Frame (24), and one Pad Tubethrough the Leg Lever (28).Wet the ends of the Pad Tubes (71) withsoap
49. Remove the decals, one at a time, from the decal sheet, and apply them to the compact trainingsystem in the locations shown in the drawing below.&
CABLE DIAGRAMSThe cable diagrams show the proper routes of the four cables on the compact training system. Thenumbers indicate the order in which the
TABLE OF CONTENTSIMPORTANT SAFETY PRECAUTIONS ... 2BEFORE YOU BEGIN ...
258"Cable (53)265" Cable (54)One end of the265' cable isattached to thebolt.71\end ofthe 265" cableis attached tothe weighttube.20
USING THE COMPACT TRAINING SYSTEMThe instructions below describe how each part of the compact training system can be adjusted. Seethe EXERCISE GUIDE a
ADJUSTINGTHEMILITARYPRESSARMFor the MILITARY PRESS or REVERSE MILI-TARY PRESS exercises (see the EXERCISEGUIDE), pivot the Military Press Arm (32) so
TROUBLE-SHOOTING AND MAINTENANCEInspect and properly tighten all parts of the compact training system each time you exercise. Replaceany worn parts im
ORDERING REPLACEMENT PARTSEach COMPACT TRAINING SYSTEM has its own MODEL NUMBER. Always mention this MODELNUMBER when requesting service or repair par
BEFORE YOU BEGINCongratulations for selecting the SEARS LIFESTYLER ®SYSTEM CXT compact training system. Theinnovative LIFESTYLER SYSTEM CXT offers an
ASSEMBLY4Assembly requires two people and will take about four hours. Due to the weight of the compact trainingsystem, it should be assembled in the p
,°=Slide one end of the 265' Cable (54) onto a3/8" x 2' Bolt (9). (The 265" Cable is the longCable that has an eyelet on one end,
6. 66Slide a Cable Trap (3) and a Small Pulley (1)onto a 3/8" x 4 1/2" Bolt (13). Route the 265"Cable (54) up around the Small Pulley.
10. Slide a Cable Trap (3) and a Small Pulley (1)onto a 3/8" x 2" Bolt (9). Route the 265" Cable(54) down around the Small Pulley. Make
814. Attach a Seat (39) to the Press Frame (20)with two 1/4" x 3/4" Bolts (6).Snap the plastic pin on the lower end of theLarge Backrest (37
17. Slide the four Bumpers (45) onto the fourWeight Guides (34).Insert the Weight Guides (34) into the indicat-ed holes in the Base (19). Attach the u
Comments to this Manuals